Invisible Speakers are the pinnacle of the Sonance “Designed to Disappear” strategy. This product is intended to be installed by professional AV integrators and installers only.=> Sonance Invisible Series IS6 Speakers (Pair) This product manual is intended to serve as a general guideline for most applications. It is the installer’s responsibility to ensure this product is installed in accordance with local building codes and regulations. Do not block any ventilation openings.Consult a local authority for specific requirements, regulations, and building codes of the jurisdiction in which this product is to be installed. Only use attachments/accessories specified by Sonance.ĭo not install near a heat source such as radiators, heat registers, stoves, fireplaces, or other apparatus (including amplifiers) that produce heat.Install in accordance with the manufacturer’s instructions.To be installed in indoor locations only.Refer all servicing to qualified service personnel.Together these performance and installation improvements redefine what is possible from an invisible speaker The Sonance Invisible Series speakers featuring Motion Flex Technology offer a suite of advancements in speaker engineering that delivers unparalleled acoustic performance and installation enhancements that allow a wider range of applications with more consistent results. This line of full-range speakers and woofers incorporate Wave Flex drive units, carbon fiber Air Flex woofers, and acoustically-isolated baffles, allowing for up to 180 degrees of smooth off-axis response. The innovative Sonance DISC System enables nondestructive measurement of the finish thickness for consistent and repeatable installation results. Sonance DSP amplifier presets should be used to maximize the performance of any Invisible Series system. Compatible with 1/2” (12.5mm) & 5/8” (15mm) drywall using included shims.Supply your own shims for thicker substrates Per-transducer poly fuses integrated into every speaker allow extra protection of each transducer from over-current.Integrated, sealed metal rear enclosure for consistent installs in commercial applications.Embedded depth discs allow the installer to verify the finish material thickness with the optional DG-1 DISC System Depth Gauge (SKU 93491).30W multi-tap 70V/100V transformer with 4-ohm bypass and Sonance Laminated Core Technology for full-range, high-fidelity audio reproduction.įinish-up-to or finish-over with up to 1/8” (3mm) flexible topping compound or finish material. When using speaker wire without conduit, run the wire through the hole on the terminal cover plate.Using a #2 Phillips head screwdriver remove the two screws securing the terminal cover plate.The Sonance Invisible Series IS6T includes a 70V/100V Sonance Laminated Core Transformer with an adjustable tap. The wire needs to be clamped as required by national or local codes. Connect the wires to the terminal block being certain to connect the positive wire to the terminal marked + and the negative wire to the terminal marked –. Using a flat-head screwdriver set the transformer tap to the correct tap setting for your installation.When using conduit attach the conduit connector to the terminal cover plate then connect the wires to the terminal block being certain to connect the positive wire to the terminal marked + and the negative wire to the terminal marked –. We strongly recommend testing the system with music to determine the correct output level. WARNING: Do not mount and finish over the speaker until you have selected the necessary tap setting to achieve the desired volume level. If necessary, re-select a lower or higher tap setting.Īfter selecting a given tap, play the speaker with an actual audio signal to verify the speaker provides adequate volume. Sonance DSP Amplifiers are recommended for use with the IS6T speaker. When using the IS6T in 70V/100V, we recommend the Sonance DSP-2-750 MKII. These amps have preloaded curves to optimize the performance of Invisible Series speakers and woofers. Preconfigured curves for various finish types and thicknesses allow for effortless calibration without the need for additional Sonance invisible series series# Sonance DSP Amplifiers are rated down to 4 Ohms and are stable to 2 Ohms. Never run more than two Invisible Speakers in parallel on one amplifier channel. NOTE: Pay attention to Sonance IS speaker-rated RMS power handling. Select an amplifier with max RMS watts per channel at 4 ohms that closely matches or is less than the IS speaker’s rated power handling (see page 16).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |